Pittsburgh, October 1, 2008 – As businesses, governments and individuals continue to look for ways to reduce their energy consumption, light emitting diode (LED)-based lighting has taken off as one of the most sought-after technologies driving these efforts. To advance its...
Pittsburgh – October 8, 2008 – For decades, the resin transfer molding (RTM) process has been a preferred method for manufacturing composite parts. Resins used in the process have traditionally included polyester, vinylester and epoxy, to name a few. However, Bayer...
Pittsburgh, October 1, 2008 – As businesses, governments and individuals continue to look for ways to reduce their energy consumption, light emitting diode (LED)-based lighting has taken off as one of the most sought-after technologies driving these efforts. To advance its...
Pittsburgh – October 8, 2008 – For decades, the resin transfer molding (RTM) process has been a preferred method for manufacturing composite parts. Resins used in the process have traditionally included polyester, vinylester and epoxy, to name a few. However, Bayer...
Pittsburgh, October 1, 2008 – As businesses, governments and individuals continue to look for ways to reduce their energy consumption, light emitting diode (LED)-based lighting has taken off as one of the most sought-after technologies driving these efforts. To advance its...
Pittsburgh – October 8, 2008 – For decades, the resin transfer molding (RTM) process has been a preferred method for manufacturing composite parts. Resins used in the process have traditionally included polyester, vinylester and epoxy, to name a few. However, Bayer...
Pittsburgh – Sept. 17, 2008 – For years, the mobile diagnostic carts used throughout the automobile industry have created challenges for automakers. The carts’ side rails were typically made from extruded steel tubing and sheet metal. When the carts were...
Pittsburgh, October 1, 2008 – As businesses, governments and individuals continue to look for ways to reduce their energy consumption, light emitting diode (LED)-based lighting has taken off as one of the most sought-after technologies driving these efforts. To advance its...
Pittsburgh – October 8, 2008 – For decades, the resin transfer molding (RTM) process has been a preferred method for manufacturing composite parts. Resins used in the process have traditionally included polyester, vinylester and epoxy, to name a few. However, Bayer...
Pittsburgh – Sept. 17, 2008 – For years, the mobile diagnostic carts used throughout the automobile industry have created challenges for automakers. The carts’ side rails were typically made from extruded steel tubing and sheet metal. When the carts were...
Pittsburgh, October 1, 2008 – As businesses, governments and individuals continue to look for ways to reduce their energy consumption, light emitting diode (LED)-based lighting has taken off as one of the most sought-after technologies driving these efforts. To advance its...
Pittsburgh – October 8, 2008 – For decades, the resin transfer molding (RTM) process has been a preferred method for manufacturing composite parts. Resins used in the process have traditionally included polyester, vinylester and epoxy, to name a few. However, Bayer...
Pittsburgh – Sept. 11, 2008 – Bayer MaterialScience LLC recently introduced its proven family of Blendur® polyurethane resin systems to the North American market at the COMPOSITESWORLD Expo, held Sept. 3-5 in the Renaissance Schaumburg Hotel and Convention Center,...
Pittsburgh – Sept. 17, 2008 – For years, the mobile diagnostic carts used throughout the automobile industry have created challenges for automakers. The carts’ side rails were typically made from extruded steel tubing and sheet metal. When the carts were...
The enhanced formulation of new Dyna-Purge® SF works faster and requires less material than other types of commercial purging compounds, and lowers the cost-to-purge up to...
Troy, Mich. – September 25, 2008 – Inteva Products, LLC and A. Schulman, Inc. (Nasdaq-GS: SHLM) announced today a licensing agreement to provide automotive manufacturers with an industry-leading technology for use in the interior manufacturing process. Inteva’s...
The M-175 machine features 175 tons of perform clamp, giving you the ability to run high cavitation molds using standard Injection Blow Molding approved resins.
...
Plastic Commodity (24)
Bookmark this page